![]() Even using 8 GAUGE wiring, it should still stay on but this AMP is staying in protect mode. I have also purchased 0 GAUGE wiring kit so if they send a new one out, I will have the correct wiring kit to power the AMP rather than 8 GAUGE wiring kit. They said to send it to AMP doctor and they will repair the AMP for me and send it back which I agreed too at the start but then thought about it again during the day and thought why should I be getting a repaired AMP back when I paid for a brand new AMP? Waiting for Monday so I could say to them that I will send the AMP back to them and request a brand new AMP to be sent or a full refund to be sent to me, If they do not agree, then I will have to go through it with PayPal. Spoke to the guys on the phone and they told me they tested the AMP out for 26 minutes at 1 OHM load and it was running perfectly fine before they took all the cables of and sent it to dispatch. I think it is a dead AMP yet it was sold to me through ebay as BRAND NEW. If it is not sound going through to the terminals then what else could it be that is causing smoke to come out of my speaker cables? That could explain why the speaker cables where getting very hot if I connected them to the terminals. I haven't checked continuity however I did check AC voltage set at 200 and connected the Red to positive and black to negative on the speaker output terminals and the reading was reading 30 and jumping to 28 constantly, did not go to 0, This was when there where no RCA cables attached. Could they have damaged something while disconnected the equipment? I am honestly not sure what is wrong with it and have spent more than 7 hours trying to get it to work and still nothing!! ///y282845/emoticons/ Is it a faulty AMP? The AMP is brand new and the company said they tested it at 1 Ohm load for 26 minutes before they sent it out so they reckon the AMP is completely perfect. I added more speaker wire so that the wire itself wouldnt get hot and that seems fine now but still no sound and the AMP stays in protect mode! Have tried my sub woofer with a different AMP in a different car and the sub works perfectly fine so it is not the problem.ġ2V and 12V remote are receiving 12volts so they cant be the issue too. ![]() I have changed the ground point 2 times now > The AMP itself was quite hot too and there was no load on the AMP itself as the gain was barely turned up. Moved the speaker cable a little and smoke came from the ends of the cable from the AMP side as well as it being quite hot to touch. Took it all off again and put it back into the car and this time the protect mode stayed permanently and still no sound. The sub woofer speaker wire was quite hot from the AMP side. The AMP would cut out and go into protect mode. The AMP was making the sub woofer bump a little but if I turned the volume higher. Spent 6 hours on this and then took it all inside and used an old car battery to power the AMP up and used my phone as the audio source. I removed the fuse and put it back and now it gets 12 volts but there was no output from the AMP itself. The first time I connected it all up, the AMP was only getting around 10 volts. The AMP is capable of 1000 watts RMS at 2 ohms so I know that is correct. The Subwoofer I am trying to power is a Pioneer TS-W3004SPL wired in parallel at 2 ohms. My AMP is a Sound Stream P1.1500D and it is brand new received yesterday. Last Updated on: Novemwith New Soundstream Picasso P1.If anyone can please help me with this I would be great full. $400 Each.2 X 400 RMS 4 Ohm 2 X 800 RMS 2 Ohm 1 X 1600 RMS 4 Ohm Mono RUBI™ (Rapid-Use Branched Impulse) Proprietary power supply topology STA. This one is made in USA before Soundstream switched to Overseas production. Brand New Soundstream Van Gogh VGA1600.2 Amp - $400 (joplin)īrand New Soundstream Van Gogh VGA1600.2 Amp.It can still be used as a 2 channel amplifier with no issues and still has a lot of music left to play.100 watts x 2 or 260 watts. This is a 4 channel amplifier BUT the rear channels stopped working. Sounstream Picasso Nano cute little amp is in need of a good home. Soundstream Picasso amplifier - $35 (Post Falls).New Soundstream Picasso P1.1500D 1500 Watt Monoblock Amplifier / Amp - $130 (Salida or Howard).New Soundstream Picasso P1.1500D 1500 Watt Monoblock Amplifier / Amp - $140 (Salida or Howard). ![]() New Soundstream Picasso P1.1500D 1500 Watt Monoblock Amplifier / Amp - $250 (Salida or Howard)īrand new in box.Includes what is shown.No offers please.I have access to e-mail contact only.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |